Sélecteur d’examples de pièces coulées en alliage de zinc
There are 24 studies matching your search criteria.
Bajonett XT-A
The 3-piece bayonet XT -A is assembled into a circular piece and provided with a cover plate. The part is designed so that it dissipates, together with an inlay heatsink , the heat generated by the installed LED ( 60-80°C ) . The casting challenge is to achieve defect...
Capstan Retainer
Precision and strength are important design considerations for the minicartridge tape drive. The capstan retainer is a good example. This part is actually two separate components cast together–a Torx head screw with an integral retainer sleeve. To produce the...
Connector for Radio AM/FM Signal
The part has the following attributes: Part functionality : Allows one single part in zamak for electrical connection (interface) and mechanical (coding + retention) Connector function: Allow the transmission of an RF AM FM signal Reflow soldering assembly process:...
Connector Housing – Berg Electronics MICROPAX ™ connectors
MICROPAX connectors have very demanding specifications which are met by zinc die casting, including: 1. Complex design requirements to accommodate a variety of connectors, ranging from 40 to 200 connecting pins. 2. Flatness across the mounting plane within +/- 0.005...
Control Handles and Mounting Box
ZA-12 graphite permanent mould castings are used for the gunner’s control handles and mounting box because the process is an economical low-volume casting method. ZA-12 also provides the handles with the density to simulate steel. Graphite permanent mould...
Cover Plate e-drive
The part is used in a drive system as a special shield to guarantee a good air ventilation and with that a perfect cooling of the system. Technical details about the drive system: -Technology: Integrated drive system motor -Power Range: 60 W up to 150 kW -Speed Range:...
Drive Beck
The drive deck for Cherokee’s 5-1/4 in. WORM optical drive utilises a ZA-12 graphite permanent mould casting. From the start, graphite permanent mould was the process of choice because of its economical tooling cost, good dimensional control and low-volume...Einbaudose Speed TEC
Deutliche Kosteneinsparung durch Substitution einer nachträglichen mechanischen Bearbeitung. Process: Zwei im Bauteil innen liegende und um 110° zueinander versetzte Hinterscheidungen, die mit Hilfe zweier im Durchmesser 17 mm Formkern integrierten Schrägschieber...
Electronic Connector
Key benefits: Close cooperation between diecaster and customer : clipping system Modern assembling technology : no screw = no creep!! This excellent product is the result of the perfect knowledge of tooling and casting
Electronics Housing
SINAMICS Control Unit CU305 The casting is a housing for the most demanding industrial electronics. To avoid short circuits it needs to be free of residual particles. To save costs for post-processing and cleaning steps, a net-shape mold concept was developed....
Front Plates
The Accent range of wiring accessories launched by MK Electric last year makes extensive use of zinc pressure diecasting and the highest standards in both painted and plated finishes to achieve a combination of slim-line good looks and high quality feel. A mix and...
Gehäuse für Leistungselektronik
Das Gussteil ist ein Gehäuse für höchst anspruchsvolle Industrieelektronik. Es muss zur Vermeidung von Kurzschlüssen grat- und restpartikelfrei sein. Um hier den Aufwand für Nachbearbeitungs- und Reinigungsschritte zu minimieren, wurde ein geschicktes Form- und...
Gehäuseklappeeiner Kommunikationseinheit
Das Gussteil zeichnet sich insbesondere durch die innovative Gießtechnik aus, die hier serienmäßig zum Einsatz gekommt. Die Gehäuseklappe wird als Abdeckung für eine Kommunikationseinheit verwendet. Sie wird in einer Sechsfachform unter Einsatz einer angussarmen...
Getriebekopf
Der aus zwei Teilen bestehende Getriebekopf dient als Gehäuse für Elektrowerkzeuge. Die Überlagerung von rotierenden und oszillierenden Bewegungen bei sehr hohen Drehzahlen und Frequenzen, wie sie beispielsweise beim Einsatz in einem Oszillationsschleifer auftritt,...
Handle for Electrical Cabinet
This zinc alloy part is designed to raise the global quality perception of the final product. The dimensional precision of the process for the fine fitting of different sub assemblies and the long life of the mould and tooling for large production series led the...
Hausing for HSD Connector
This HSD connector (HSD = high speed data) is a part of the control units in upper segment cars. The 4-pin connector assures large volume of data transfer as compared to the standard connector with only 1 pin. The required tolerances for this miniature part are...
Heat Sink
Zinc die casting offers numerous advantages over aluminum extrusion in a number of heat sink applications. Die-cast zinc heat sinks offer one-piece construction, increased design flexibility and lower cost. One of the biggest advantages is that heat-dissipating fins...
High Tension Cage
The part is a device component warranting the operators security during the intervention on high-tension lines. Reasons for choosing zinc alloy: Complex tool design Combination of thin wall casting and rigidity Dimensional requirements e.g. internal and external...
Housing & Frame
Elements of an equipment (TYCAS) to detect the positions of approaching aircraft according to new security norms of the IATA. Economy of the process compared to traditional machining despite limited series, and to pressure diecast aluminium due to off-mould...
Microprocessor Protection Housing
Part realized in large production volumes. Easy assembly with complex shapes, competing with pressed steel sheet. Zinc Castings’ superior thermal conductivity permits faster and greater heat dissipation provided by thinner radiating fins, complementing the...
Remote Control
This design high-end remote control has tactile control without any knobs. The zamak surface was cast to a thickness of 0,6mm with less than 0,05mm tolerance on thickness. Piezo elements translate the bending of the surface into electric signals. Casting of the part...
Spot Lamp Body
By using hot chamber pressure die casting for this product, Fos Nova SpA obtained excellent results both functionally and aesthetically, whilst saving production costs. Of special interest in this part is that the casting was fed through the central opening: this...
Traffic Light Housing
The 2 parts are used as casing including and protecting the electric system of traffic lights. The material properties provides protection against vandalism and have much longer lifetime than polymer materials and due to thinner sections, lighter than the previous...